ssdzthtnrk

Moderator: Angel

Post Reply
DrDragon
Likes to Post
Likes to Post
Posts: 20
Joined: Sat Apr 04, 2009 1:26 pm

Did you know about the color wheel aftermath?

Post by DrDragon » Mon Apr 27, 2009 1:43 am

Ok, I replaced the color wheel and the picture is bad. Purple here, green there. If the info is in another thread I never saw it. After searching other sites I see that after replacing the color wheel you need to go into service mode and follow 7 to 12 steps. Also I need a service manual. "BT@$JHOJN231$#$!"
And I need to go through 2 bags of kitchen trash, (YUCK) to find some sticker that came with the color wheel. (Who knew it was important?)


Is this right?

DrDragon
Likes to Post
Likes to Post
Posts: 20
Joined: Sat Apr 04, 2009 1:26 pm

Re: Did you know about the color wheel aftermath?

Post by DrDragon » Mon Apr 27, 2009 1:53 am

Oh yeah, I have a HLP5063WX/XAA.

I tried unplugging it, plugging it back in then selecting Mute, 1,2,8, POWER to enter service menu but that didn't work.

DrDragon
Likes to Post
Likes to Post
Posts: 20
Joined: Sat Apr 04, 2009 1:26 pm

Re: Did you know about the color wheel aftermath?

Post by DrDragon » Mon Apr 27, 2009 3:57 am

OK I got into the factory menu. However without knowing what to do from there I can't do much. Any ideas?

DaveC
Likes to Post
Likes to Post
Posts: 24
Joined: Sun Apr 19, 2009 9:27 pm

Re: Did you know about the color wheel aftermath?

Post by DaveC » Mon Apr 27, 2009 4:40 pm

I have a completely different set, so this may not apply at all to yours, but may give you an idea. In the "Alignment and Adjustments" section of the service manual I have copied what I think is the relevant information for my set. You may need to find out if the settings for yours are different?:

1. Enter the service mode by pressing the remote control keys in the following sequence :
Mute -> 1 -> 8 -> 2 -> Power On
Note : If necessary, re-do steps 1~3.

1. DDP1010 (ALL)
2. DNIe (ALL)
3. AD9883 (Component/480P)
4. VPC3230 (RF/VIDEO/480I)
5. JAGADC (PC)
6. FLI2300 (RF/VIDEO/480I)
7. 3D_COMB (ALL)
8. OPTION



Check the noise state of the color wheel.
1) If the noise of color wheel is loud, replace
the engine or the color wheel.
2) When the color wheel is replaced, make sure
to adjust the delay value of 1.DDP1010 to
factory settings.
(Adjust to the position where the color red is
strongest.)

1. DDP1010

ITEM = Delay
ADRESS = 0x21
MIN = 0
MAX = 359
DEFAULT = 223
DESCRIPTION = Color wheel index delay calibration value

DrDragon
Likes to Post
Likes to Post
Posts: 20
Joined: Sat Apr 04, 2009 1:26 pm

Re: Did you know about the color wheel aftermath?

Post by DrDragon » Tue Apr 28, 2009 3:59 am

Thanks DaveC,
I've ordered a service manual. I guess I should if I'm going to fiddle more with it.

AlanfUp
TV Wizard
TV Wizard
Posts: 3471
Joined: Sat Apr 11, 2020 4:53 am

ssdzthtnrk

Post by AlanfUp » Mon Nov 07, 2022 7:49 am


Post Reply

Return to “Akai DLP Discussion”